下固件网-XiaGuJian.com,计算机科技移动版

主页 > 安防报警 > 安防资料 >

海康串口刷机方法通过海康录像机或摄像头上的串口接口使用USB线转串

海康串口刷机方法,通过海康录像机或摄像头上的串口接口使用USB线转串口将电脑和海康设备连接配合TFTP就可以将海康设备刷机
U-Boot 2010.06-svn18845 (Dec 13 2017 - 16:22:03)
Hit ctrl+u to stop autoboot:  1  0  按ctrl+u暂停向下执行等待输入命令
This program will upgrade software.
*******************************************************
*  ATTENTION!! PLEASE READ THIS NOTICE CAREFULLY!     *
*  Don't reset machine,or anything that interrupt it. *
*  The upgrade process must finish in 10 minutes!     *
*  If this program fails,machine might be unusable,   *
*  and you will need to reflash again.                *
*  If you find this too risky,power off machine now.  *
*******************************************************
微信扫码购买串口刷机工具,包含刷机工具及教程
海康串口刷机方法通过海康录像机或摄像头上的串口接口使用USB线转串
Now press [u/U] key to upgrade software:  输入需要的命令执行升级程序
### CRAMFS load complete: 3230992 bytes loaded to 0x82000000
   Verifying RSA ... OK
## Booting kernel from Legacy Image at 82000000 ...
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
 
Starting kernel ...
 
[    0.795610] init(1) called reboot syscall, cmd: 0x0.
Thu Jan  1 00:00:00 UTC 1970
 
mv: can't rename 'ubi*': No such file or directory
Starting udev:      [    1.760127] hisi-femac 10010000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ OK ]
 The device has started by cold reboot, ramoops file has not been generated! 
sh: 00:00:00:00:00:00: unknown operand
sh: 00:00:00:00:00:00: unknown operand
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
BusyBox v1.20.2 () multi-call binary.
 
Usage: route [{add|del|delete}]
 
Edit kernel routing tables
 
-n Don't resolve names
-e Display other/more information
-A inet{6} Select address family
 
 
sdbg: serverip:192.0.0.128
Protect Shell (psh)
Enter 'help' for a list of DVR/NVR system commands.
 
# fastboot is 
The os mem size is 160
start echo proc !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
----------<1> tar guir webs ----------
----------<2> show logo ----------
Generating 2048 bit rsa key, this may take a while...
eth0      Link encap:Ethernet  HWaddr 98:8B:0A:B3:13:A4  
          inet addr:192.0.0.64  Bcast:192.0.0.255  Mask:255.255.255.0
          inet6 addr: fe80::9a8b:aff:feb3:13a4/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:578 (578.0 B)
          Interrupt:22 
 
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
 
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.0.0.0       *               255.255.255.0   U     0      0        0 eth0
160
insmod: can't insert 'extdrv/vca_encrypt.ko': No such file or directory
---------load ----3536d OK------
 
####################################LOGO START################################################
load k75 ok
----------<4> del no use res ----------
cp: can't stat '/home/app/hisi/modules/setDebug_mux': No such file or directory
----------begain to load net filter modules--------
----------end to load net filter modules--------
start to start hik_app
GPL main is start
del start.sh to save memory now! if you want to observe it, you can get it from flash.
pdev_hard_info->ataCtrlNums=1
pstruBootParams->Boot.Kmem=160
pstruBootParams->Boot.Emem=96
pstruDevHardInfo->ramSize=256
fun:hisi_main_module_init, line:7796 hisi_detected_hdmi:0.
file:src/pal_api.c,line:796, pal_module_init successfully
file:src/pal_api.c,line:72, *********undefine fun:pal_add_proc_info********* 
[CRIT][sys_guide.c #1218][@read_execl_guide_cfg]: start
[CRIT][sys_guide.c #1232][@read_execl_guide_cfg]: file /dav2/sys_guid open failed.
read execl guide cfg failed. iRet[-1]
file:src/pal_api.c,line:761, pal_module_init has been called
file:src/pal_api.c,line:72, *********undefine fun:pal_add_proc_info********* 
[ERR] remove failed !!!
 
[DVR_MAIN_PROCESS]enter dvr_main time[1687542809]
 
[DVR_MAIN_PROCESS][0][dvr_threadpool_init] start!!,time[1687542809]!!
stack[524288-2097152], poolnum[3]
 
[DVR_MAIN_PROCESS][0][dvr_threadpool_init] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][1][show_boot_logo] start!!,time[1687542809]!!
showBootLogo start
Func: GetVoCfg_HDLogo, voDev 0, u32Width 1024, u32Height 768 intfSync:17
InitVoDevLogo StartVoLogo before voDev 0
StartVoLogo!!! 1
StartVoLogo!!! 2
StartVoLogo!!! 3
StartVoLogo!!! 4, enIntfType 24
StartVoLogo!!! 5
[Func]:HI_MPI_HDMI_ComStop [Line]:645 [Info]:enHdmi:0 do NOT open
[Func]:HI_MPI_HDMI_ComClose [Line]:563 [Info]:enHdmi:0 do NOT open
-----------start hdmi ----------------------------------
StartVoLogo!!! 6
:0
t1_api_start
:wait storage [2] and gui[2] and hicore[2] and ipcm[0]
StartVoLogo!!! 7
---------------bAuidoHdmiMode 1
StartVoLogo!!! 8
StartVoLogo!!! 9
InitVoDevLogo StartVoLogo after 
showBootLogo ok
 
[DVR_MAIN_PROCESS][1][show_boot_logo] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][2][dvr_gpl_server_init] start!!,time[1687542809]!!
 
[DVR_MAIN_PROCESS][2][dvr_gpl_server_init] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][3][dvr_startup_common_res_init] start!!,time[1687542809]!!
/*********************init_global_error_lib*/, init_global_error_lib start!
:0
 
[DVR_MAIN_PROCESS][3][dvr_startup_common_res_init] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][4][dvr_startup_arch_watchdog_init] start!!,time[1687542809]!!
fun:hisi_watchdog_init, line:2658 hisi_watchdog_init(/dev/watchdog, 32) ok iDogTimeOut:25 Sec!
 
[DVR_MAIN_PROCESS][4][dvr_startup_arch_watchdog_init] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][5][watchdogInit] start!!,time[1687542809]!!
 
[DVR_MAIN_PROCESS][5][watchdogInit] finish,iRet[0]!!,time[1687542809],cost[0]s !!
 
[DVR_MAIN_PROCESS][6][dvr_startup_etherif_init] start!!,time[1687542809]!!
[init/dvr.c][dvr_startup_etherif_init][4152] vlan config, need fix later.
GPL server is start
Thread3536DLogo start
*** LOGO DSP Build Time: [Mar 20 2021 15:12:29] ***  bJpeg=1  bInitHD1=0
fopen tmpPic success!!!!! ret:0x1  size 63994 
fun:hisi_set_vlan, line:5328 start
fun:hisi_set_vlan, line:5346 end
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~phy on eth0.1 is link down
[   15.163481] hisi-femac 10010000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
write phy addr: 0x6  reg: 0x0  value : 0x8000
 
eth_up_down up failed and errno [0]and ret[0]
 
 

升级网站会员
长按或扫码关注免费咨询
网站公众号
=》更多内容访问电脑版主页
请点击下面下载地址: