大华DH-NVR1104HC-HDS4启动日志
时间:2024-05-24 21:28 来源:未知 作者:admin 点击:次
大华DH-NVR1104HC-HDS4启动日志，通过录像机上的串口线获取到的日志信息
IPL g1304bfa
D-1f
HW Reset
miupll_233MHz
MIU0 zq=0x003b
miu_bw_set
utmi_1_init done
utmi_2_init done
utmi_3_init done
usbpll init done......
CPU=1200Mhz
cpupll init done
SPI 54M
clk_init done
P1 USB_rterm trim=0x0000
P1 USB_HS_TX_CURRENT trim=0x0001
P2 USB_rterm trim=0x0000
P2 USB_HS_TX_CURRENT trim=0x0001
P3 USB_rterm trim=0x0000
P3 USB_HS_TX_CURRENT trim=0x0001
PM_vol_bgap trim=0x003f
GCR_SAR_DATA trim=0x0190
ETH 10T output swing trim=0x0000
ETH 100T output swing trim=0x0000
ETH RX input impedance trim=0x0000
ETH TX output impedance trim=0x0001
MIPI_HS_RTERM trim=0x0001
MIPI_LP_RTERM trim=0x0000
TX_current trimming trim[0x1A]=0x0047
TX_current trimming trim[0x1B]=0x0048
TX_current trimming trim[0x1C]=0x0047
HDMI2TX Rterm trim=0x0000
HDMI2TX_Ibias_CH0 trim=0x001a
HDMI2TX_Ibias_CH1 trim=0x001a
HDMI2TX_Ibias_CH2 trim=0x001a
HDMI2TX_Ibias_CH3 trim=0x001a
256MB
BIST0_0001-OK
Enable MMU and CACHE
Load IPL_CUST from SPINAND
QUAD MODE ENABLE
Checksum OK
IPL_CUST g1304bfa
runUBOOT()
runUBOOT()
[SPINAND]
SPI 54M
Load UBOOT from SPINAND
-Verify UBOOT CRC32 passed!
-Decompress UBOOT XZ
decomp_size=0x000a16b4
Disable MMU and D-cache before jump to UBOOT
U-Boot 2015.01-svn6402 (Sep 19 2023 - 09:20:35), Build: jenkins-GSP_DH3.3662_4X2X1XSSR621Q_linux-1213
Version: I2g#######
DRAM:
WARNING: Caches not enabled
SPINAND: _MDrv_SPINAND_GET_INFO: Found SPINAND INFO
(0xC8) (0x1)
SPINAND: board_nand_init: CIS contains part info
128 MiB
MMC: MStar SD/MMC: 0
unexpected character ' ' at the end of partition
In: serial
Out: serial
Err: serial
Auto-Negotiation...
AN failLink Status Speed:10 Full-duplex:0
Status Error!
sstar_emac
Hit any key to stop autoboot: 0
[NetUpgrade] ts_1st=0x1858
[NetUpgrade] Get Device MacAddr(6c:1c:71:2c:ed:c1)
NetUpgrade Timeout
[NetUpgrade] ts_1st=0x1858, ts_2nd=0x1c45, delt_ts=0x3ed
mtdparts has been init.
### CRAMFS loading 'bmp_logo.bmp' to 0x2e200000
Loading: T T T
Retry count exceeded; starting again
autoup - load update file from server
Usage:
autoup
## Booting kernel from Legacy Image at 2ca00000 ...
Image Name: MVX4##I2M#g#######KL_LX409
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 3566284 Bytes = 3.4 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Uncompressing Kernel Image ...
[XZ] !!!reserved 0x21000000 length=0x 1000000 for xz!!
XZ: uncompressed size=0x620000, ret=7
OK
atags:0x20000000
Starting kernel ...
长按或扫码关注免费咨询
=》更多内容访问电脑版主页
请点击下面下载地址：